YASTUDIO Mark
| En
シティカブリオレ アイコン VW タイプ2 バス アイコン ダイハツ エッセ アイコン

« HONDA CITY CABRIOLET TURBO2


Num of articles:  

82. Interior completed for now

E:2022.08.13 / W:2022.08.11

81. Thermometer with an original panel

Entry:2022.08.11 / Work:2022.08.09←06
HONDA CITY CABRIOLET TURBO2 : An In/Out thermometer panel and the fog lamp switch panel 16

I put the fog light switch in the blank panel section where there are two locations, and since one of them was free, I modified the blank panel to install a digital temperature gauge that can display the temperature inside and outside the car.

When checked side by side with the fog light switch panel, the surface texture and layout were not quite right, so the fog light switch panel was also remade.

In both cases, a cover sheet was cut from the plastic case that housed the phone cover, a smoke film was applied, and a cutting sticker sheet cut with a cutter plotter was applied over it.

The fog light switch was too dark with the original filament bulb, so a green high-intensity LED was hot-bonded to the divider board inside the switch to adjust the position and illumination.

An In/Out thermometer panel and the fog lamp switch panel 15

Place the sign alongside the previously made fog light switch and design the sign to align with the LED display portion of the thermometer.

An In/Out thermometer panel and the fog lamp switch panel 14

Drill holes at the display locations and cut ribs of the back of the blank panel so that it can be mounted on the thermometer unit .

An In/Out thermometer panel and the fog lamp switch panel 13

The sheet to be applied to the front side is cut from the plastic container in which the phone cover was housed, and the smoke film is applied.

An In/Out thermometer panel and the fog lamp switch panel 12

Stick a sticker sheet sign cut out with a cutter-plotter on top of the smoke film.


An In/Out thermometer panel and the fog lamp switch panel 11

Apply double-sided tape to the blank panel and remove the front panel of the thermometer.

An In/Out thermometer panel and the fog lamp switch panel 10

The blank panel and the thermometer unit are combined, and a sheet with a signature was attached.

The LED emitting surface is slightly set back, so it looks one-sided unless viewed from the front.

An In/Out thermometer panel and the fog lamp switch panel 09

When the switch is set and checked again, the texture is different from that of the fog lamp switch, and there is no sense of unity in the sign.

In other CITY equipped with rear wipers, washers, and defoggers, this is where the switch for that goes. The Cabriolet does not have them, so they were left blank.

An In/Out thermometer panel and the fog lamp switch panel 08

When lit, it is not at the correct height, which is unfortunate.

The choke was originally attached on the right side of the air temperature gauge, and since the turbo engine was transplanted and changed from carburetor to injection, the choke was removed and the voltmeter was housed.

An In/Out thermometer panel and the fog lamp switch panel 07

I decided to redesign the fog light switch and studied the layout.

The left end was original, next adjusted the layout and size and decorated the push buttons. Last, we did the same for the thermometer and sign, and designed the 'ON' sign to match the digital typeface.

An In/Out thermometer panel and the fog lamp switch panel 06

For the lighted sign inside, a black cutting sheet with letters cut out of it was attached to a transparent sheet, and a green transparent cellophane sheet was attached from the back.

An In/Out thermometer panel and the fog lamp switch panel 05

To prevent light from leaking from the illuminated sign, we masked all but the sign and push-switch areas with black cutting sheets.


An In/Out thermometer panel and the fog lamp switch panel 04

Using the opening in the black sticker affixed for the mask as a guide, cut out the push switch portion and affix the sign cut from the white cutin sheet.

An In/Out thermometer panel and the fog lamp switch panel 03

Attach the sheet to the switch and set again. Since there are buttons, they cannot be exactly the same, but I think we can give the impression that they are all in the same design.

An In/Out thermometer panel and the fog lamp switch panel 02

Since the original filament bulb was too dark, a green high-intensity LED was obtained, hot-bonded to the divider inside the switch, and installed.

An In/Out thermometer panel and the fog lamp switch panel 01

From the driver's seat, you can see this when you raise your body a little.


80. Fog lamp switch

E:2022.07.31 / W:2022.07.25

79. Main power and starter switch

E:2022.07.30 / W:2022.07.24

78. LED ring projector headlight

E:2022.07.18 / W:2022.07.17

77. CITY Meeting in Fukushima 202206

E:2022.07.02 / W:2022.06.19

76. Air intake tube

E:2022.06.12 / W:2022.06.12

75. 2022 HONDA in The Showa Era Meeting

E:2022.06.11 / W:2022.06.05

74. Light control system

E:2022.06.04 / W:2022.06.04

73. 34th MOONEYES Street Car Nationals

E:2022.05.22 / W:2022.05.15

72. Mirror writing sticker

E:2022.05.12 / W:2022.05.08

Num of articles:  

- END -